Wavecom Instruments Fully Integrated Test n Print Unit User Manual

Testing of Electrical Equipment

Many testing personnel have some reservations in testing sensitive, electronic equipment using a 500V DC

insulation test. There is a perceived fear of causing internal damage from over voltage. With the introduction on

the TnP Range of appliance testers, these concerns are alleviated.

The TnP Range of electrical portable appliance testers is safe to test electronic equipment as the tests are

carried from Active-Neutral (shorted by a relay inside the tester) to Earth. No dangerous voltages pass through in

this mode to the internal components of the DUT (Device Under Test). If these tests are done using an

Insulation Tester only and the user tests Active to Neutral, this would be a cause of potential damage, this is

why the TnP product range is far safer to use.

Some changes may be required in certain configurations where fitted surge protection devices (MOV's) in the

DUT may cause a failed test result. Applying 500V in this these situations can cause the surge protection

devices to trip, therefore conducting the applied voltage to earth, thus showing a failure of insulation. In these

instances the test voltage should be changed to 250V then retest. If DUT still fails, check with the DUT

Operators Manual or an electrician. [for details see - ‘Double Insulation Test’ 250/500VDC to change test

voltage].

Under these circumstances, it would be difficult for any damage to occur to either the surge protection device or

the DUT, as there is insufficient current generated by the TnP test unit.

Leakage Test:

If there are any doubts with insulation testing of the equipment, the standard

(AS/NZ3760 since 2001) allows for an alternative test method. A Leakage Test can be performed instead. (The

TnP – Series are designed to perform these tests).

NOTE: 10Amps MAXIMUM Resistive Load only (Standard TnP Series units).

A Leakage Test applies power to the Device Under Test (DUT) and measures the imbalance of leakage current

from the DUT between the active and neutral conductors. The leakage is tested to the limits specified in the

standard and a Pass/Fail result as well as a digital reading is provided to ensure that the user gains as much

information as necessary.

Earth Continuity Test, commonly called EARTH BOND TEST:

Note: Part of normal (Class 1 test) procedure

Use supplied IEC–Croc clip lead or optional accessory ‘WCM-Probekit’.

The TnP.500 unit conducts earth continuity tests at Approx. 200mA. Continuity tests at higher currents are

not required or recommended on certain equipment as this may cause severe damage or premature failure to

the Device under test (see AS/NZS 3760:2010).

Unique Earth Bond Test Feature

Note: Test time with the new TnP-500 series can now be user controlled. This function enables testing personnel

to extend the Earth Bond test time by 30 second increments!

This is achieved by momentarily pushing the ENTER button once, during the test.

The TnP-500 will then add 30 seconds to the test time for ENTER button press.

This feature has been incorporated to provide extra time to achieve an adequate physical connection, or confirm

any possible INTERMITTENT issues. There may be situations where the condition of equipment, coatings

applied, or suspect wiring breaks may alter the earth connection path of the device under test.

Benefit to test personnel is to save time by not having to continually repeat tests in a less than perfect situation.

3 Phase Testing: *Optional equipment required

3 Phase appliances can be tested by the TnP series appliance testers. As the insulation tests are from Phase to

Earth, only a 500V insulation test is required. This test may be carried out by using the optional adaptor ‘WCM-

3PH-MADP’ [See ‘Optional Accessories’ for details.]

Note: The TnP500 series will not perform a 3 Phase Leakage test.

Contact Wavecom Instruments Pty Ltd for information on appropriate testers.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 25 26

Kommentare zu diesen Handbüchern

Keine Kommentare

Philips QT4019/15 Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Haarschneider & Haarschneidemaschine Philips QT4019/15.
Wir stellen 1 PDF-Handbücher Philips QT4019/15 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung

Philips QT4019/15 Bedienungsanleitung (9 Seiten)

Marke: Philips | Kategorie: Hair trimmers & clippers | Größe: 0.58 MB |

Inhaltsverzeichnis

QT4021, QT4019

FRANÇAIS

ITALIANO

NEDERLANDS

PORTUGUÊS DO BRASIL

Weitere Produkte und Handbücher für Haarschneider & Haarschneidemaschine Philips

Modelle	Dokumententyp
NT1150/10	Bedienungsanleitung Philips Nosetrimmer series 1000 Komfortabler Nasen- u. Ohrenhaartrimmer NT1150/10 Bedienungsanleitung [bg] , 98 Seiten
HC7460/13	Bedienungsanleitung Philips Hairclipper series 7000 Haarschneider HC7460/15 Bedienungsanleitung [bg] , 126 Seiten
HC3100/13	Bedienungsanleitung Philips Hairclipper series 3000 Home clipper HC3100/13 User manual, 6 Seiten
QC5170/00	Bedienungsanleitung Philips κουρευτική μηχανή do it yourself QC5170/00 Εγχειρίδιο χρήσης, 92 Seiten
BT7204/85	Bedienungsanleitung Philips Beardtrimmer series 7000 Vacuum beard & stubble trimmer BT7202/13 User manual, 2 Seiten
QP6520/60	Bedienungsanleitung Philips OneBlade Pro Gesicht QP6510/64 Bedienungsanleitung, 264 Seiten
SBT720/15	Bedienungsanleitung Philips Star Wars special edition Vakuum-Bartschneider SBT720/15 Bedienungsanleitung, 216 Seiten
QC5099/00	Bedienungsanleitung Philips Hairclipper series 1000 Haarschneider QC5099/00 Bedienungsanleitung, 94 Seiten
QC5055/40	Bedienungsanleitung Philips Haarschneider QC5055/40 Schnellstartanleitung, 2 Seiten
HP6364/00	Bedienungsanleitung Philips Präzisionstrimmer HP6362/00 Bedienungsanleitung, 11 Seiten
QC5005/30	Bedienungsanleitung Philips Hair clipper QC5005/10 User manual, 9 Seiten
QC5070/80	Bedienungsanleitung Philips Hairclipper series 1000 Haarschneider QC5070/80 Bedienungsanleitung, 100 Seiten
QC5053/00	Bedienungsanleitung Philips Hair clipper QC5053/00 User manual, 112 Seiten
QC5115/15	Bedienungsanleitung Philips Haarschneider f. d. ganze Familie QC5115/15 Bedienungsanleitung, 5 Seiten
NT9125/15	Bedienungsanleitung Philips Nosetrimmer series 3000 waterproof detail trimmer NT9125/15 User manual [ro] , 3 Seiten
QC5053/00	Bedienungsanleitung Philips Haarschneider QC5050/01 Bedienungsanleitung [sk] , 92 Seiten
QC5005/30	Bedienungsanleitung Philips Hairclipper series 1000 Haarschneider QC5005/10 Bedienungsanleitung, 8 Seiten
HP6379/00	Bedienungsanleitung Philips Body Perfect Bikini-Trimmer HP6379/00 Bedienungsanleitung, 104 Seiten
QT4015/16	Bedienungsanleitung Philips Beardtrimmer series 3000 Barttrimmer (Dreitagebart-Funktion) QT4015/16 Bedienungsanleitung [bg] , 96 Seiten
QC5055/00	Bedienungsanleitung Philips Hairclipper series 1000 Zastřihovač vlasů QC5055/00 Uživatelská příručka [bs] [hr] [sr] , 2 Seiten

Wavecom TT040-50 Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Barcodeleser Wavecom TT040-50

Philips QT4019/15 Handbücher

Philips QT4019/15 Bedienungsanleitung (9 Seiten)

Inhaltsverzeichnis

Weitere Produkte und Handbücher für Haarschneider & Haarschneidemaschine Philips